SOLENOID VALVE RANGE
STANDARD SOLENOID VALVE
Standard solenoid valves are used in domestic and professional appliances such as washing machines, dish washers and other electrically conducted mechanisms that operate with water.
Provides safe conveyance, distribution and control of water services in a household and industrial appliances by opening or closing the passageways.
The valve can be made in combination of single, double or triple valve body.
DIRECT ACTING SOLENOID VALVES
Direct acting solenoid are independent of the incoming water pressure using a diaphragm directly linked to the armature. When the coil is energised the armature lifts the seal from valve orifice thus allowing flow through the valve.
They are supplied normally closed and provide effective on/off control of the liquid under low pressure applications typically less than 0.2 bar. The range is available with the following approvals : WRAS , NSF , UL/CSA and ENEC.
An electrically operated direct acting solenoid valve is primarily used as a drain valve in cold water drink dispensers, water tanks and similar appliances. It operates in a pressure range of 0 to 0.2 bar with direct action only.
The valve can be made in combination of single, double or triple valve body.
LATCHING/BI-STABLE SOLENOID VALVES
Through the use of a magnet, the latching valves are bi-stable which allows them to stay in either state indefinitely without drawing any power. To shift the valve from one state to another, a short 25 millisecond DC voltage is applied to the coil. To shift the valve back, a reverse polarity pulse is applied. Result is an extremely low power usage and negligible valve coil temperature rise, subsequently providing very long battery life. Latching valve is inbuilt in automatic water faucets, urinal flushing systems, auto and sensor taps, vending machines, irrigation systems etc.
We can provide electronic control modules that are used in conjunction with bistable valves or complete sets including valve, electronic module and housing.
Latching solenoid valves, also referred to as bi-stable solenoid valves uses a permanent magnet attached to the armature, when energised with short 250msec 6 volt pulse the armature is forced into either open or closed state depending on the signal polarity. They provide effective on/off control of water services ranging from 0.2 – 10bar where a constant supply of electrical power is either not appropriate or available. The range is available with the following approvals : WRAS , NSF , & UL/CSA.
The valve can be made in combination of single, double or triple valve body.
PROPORTIONAL SOLENOID VALVES
The Proportional Solenoid Valve offers the same On/Off control as standard Pilot-Operated Solenoid Valves but with the added functionality to control the flow of water passing over the valve orifice. Proportional control is offered across hot and cold water supplies from 0.5 up to 12 litres per minute within dynamic pressure range from 0.5-10 bar.
It provides variable water flow control via electronic PWM drive with feedback loop for flow and other critical parameters. It is used in electrically pumped and/or heated showers and taps.
The valve can be controlled using 24VDC power supply or pulse width modulated signal to provide variable control when used in closed loop systems.
The valve can be made in combination of single, double or triple valve body.
SERVO ASSISTED SOLENOID VALVES
The Servo operated pilot valve is designed for low power 12VDC supplies with maximum 3 watts. The valve utilises a unique servo system which in turn decreases the power required whilst maintaining control of water supplies from 0.2 to 10bar.
The range is available with the following approvals : WRAS , NSF , & UL/CSA.
Servo solenoid valve controls fluids in applications operated on DC power supply, where power consumption is of the essence.
The valve can be made in combination of single, double or triple valve body.
CUSTOM MADE VALVES
Biomaster Valve
Carbonator Valve
Cartridge Valve
Double-Dispense Valve
Manifold Valve
Micro-Membrane Valve
Valve (with pressure reducer)
Products & Services
Solenoid Valves
Full range
Door Locks
Push-push or push-pull
Switches
DS & RS type
Pumps
Micro membrane pump
Flexible Hoses
Full range
Services
Moulding Design
Plastic injection moulding
Coil Winding
For industry
Overflow Protection
Prevent water leakage
Product Assembly
Technical expertise
Product Development
From draft to realisation
Address
Eki d.o.o
Majer 27
SI-8340 Črnomelj
Slovenija
Contact
+386 (0)7 30 53 162
eki@eki.si